Microscopy basics for medical undergraduate students:

Microorganisms are so called because they are so small that they can not be ordinarily seen using unaided eye. The optical instrument that magnifies the image of these organisms that enables us to view their morphological features is a microscope.

Antony van Leeuwenhoek is often considered as the father of microscopy, although compound microscopes were actually invented much before. A compound microscope contains several sets of lenses that magnify the image at different levels. Typically, the image is magnified initially by the objective lens and then again by the eye piece before it reaches the eye.

Most bacteria measure in the range of 0.5 to 4 µm (micrometer NOT microns). Mycoplasma and Coxiella are the shortest among bacteria and Spirochetes the longest. Viruses are ultramicroscopic structures; they can’t be seen by compound microscopes. They can be visualized by electron microscopes and their measurements are in nm (nanometer). The Å (Armstrong units) is the unit of measurement for still smaller particles.

1 mm = 1000 µm

1 µm = 1000 nm

1 nm = 10 Å

Various types of microscopes are:

• Simple (dissection) microscope
• Compound microscope
• Darkground microscope
• Phase contrast microscope
• Fluorescent microscope
• Polarisation microscope
• Interference microscope
• Atomic force microscope
• Electron microscope

Principles of microscopy and concepts:

Magnification: This represents the number of times the image of a specimen is amplified. 10x means the size of the image is increased by ten times. The magnifying power of the lens is limited. After a certain point the magnification results in a blurred image and is termed empty magnification. Even with the best optics, 1400x is the highest useful magnification achieved. Magnifying power of an objective is determined by the dividing the optical tube length by the focal length of the lens. Optical tube length is the length of the microscope body tube between the nosepiece opening, where the objective is mounted, and the top edge of the observation tubes where the eyepieces are inserted. In most microscopes, it is fixed at 160mm.

Low power dry objective          160/16 = 10x

High power dry objective          160/4 = 40x

Oil immersion objective             160/1.7 = 94x or approximately 100x

Numerical Aperture of the lens is an important consideration in optics as it dictates the angle at which the light enters it. The light-gathering ability of a microscope objective is quantitatively expressed in terms of the numerical aperture. Higher values of numerical aperture allow increasingly oblique rays to enter the objective front lens, producing a more highly resolved image.

It is defined by the following formula: Numerical Aperture (NA) = n × sin(θ)

Where n is the refractive index of the medium between the object and the objective

θ is one-half the angular aperture (angle of aperture is the angle formed by the two most divergent rays of light which enter the objective, starting from the center of the object )

Refractive index of oil is 1.5 and that of air is 1.0.

NA of dry objective: 1 x sin 90^o = 1, but practically the highest practical numerical aperture of a dry lens is 0.95.

NA of oil immersion objective: 1.5 x sin 90^o = 1.5, however in practice only 1.4 is achieved for apochromatic objective and 1.3 for achromatic objective.

Limit of resolution or resolving power: In simple words, it is the ability to see two closely placed dots as two separate dots. If the distance between the two points is lessened, it would appear as a single point. It is expressed quantitatively as limit of resolution. The resolution of human unaided eye is 200 µm. This means that human eye can not see objects small than 200 µm. The resolving power of compound microscope is 0.2 µm and that of electron microscope is 1-10 nm. The limit of resolution depends on the wavelength of the light used. Resolution increases with the decreasing wavelength of light. Violet colour light offers more resolution that red coloured light. Electron beams, which have very low wavelength offers maximum resolution. It is calculated by using formula:

_{LR =} 0.61 x wavelength of light

            Numerical aperture

For example, if green light of wavelength 0.55 µm is used and oil immersion objective with NA 1.4 is used, the maximum resolution obtained is 0.24 µm

0.61 x 0.55 _{= 0.24 µm}

      1.4

Definition: This is the capacity of the objective to render the outline of the image clear and distinct. Definition of an image is disturbed by spherical or chromatic aberrations. The central part of the image is usually well focused but the edges may suffer some aberration, which are of two types; spherical or chromatic. In spherical aberration, the periphery of the image appears out of focus. This happens because all the light passing through the lens doesn’t condense at the same point. In chromatic aberration, the light is split into different colours at the peripheral part of the image since the edges of the lens act like a prism. The aberrations can be corrected by using achromatic or apochromatic lenses.

Parts and functions of compound microscope:

Source of light: Brightfield microscope uses visible light for illumination; specimen appears against a bright background. In brightfield microscope, the source of light is sunlight or indoor bulbs, or inbuilt lamps. The inbuilt lamps are made up of low voltage tungsten filament lamp or more recently LED lamp.

Condenser: The parallel beam of light from natural or artificial source is condensed into a cone of light that illuminates the specimen or the object (smear on slide) by the sub-stage condenser. If the source of light is sunlight or indoor bulbs, the light is diverted to the condenser using the mirror. Concave mirror is used when low or high power objective lenses are used, whereas plane mirror is used when oil immersion objective lens is used. Mirrors are absent when in-built lamps are used. The condenser consists of series of lenses, which focuses the light to the object placed on the stage. Kohler illumination ensures that the diffuse light of uniform brightness is available without the view of the source of light. Various types of condenser in use are Abbe, Paraboloid and Cardoid condensers. The Abbe condenser (which is named after its inventor Ernst Karl Abbe) is the simplest of condensers that contains two lenses. The condenser can be lowered or raised according to the requirements. The condenser is lowered while using low power dry objectives, and raised while using oil immersion objectives.

Iris diaphragm: The amount of light passing on to the specimen from the condenser is regulated by using iris diaphragm. Light is reduced by closing the diaphragm partially for use with dry objectives. Oil immersion objectives require maximum light and this is achieved by keeping the iris diaphragm fully open.

Objectives: The light passing through the object (specimen) enters the objective lens. Typically, most microscopes have four objective lenses mounted on a revolving nose piece. The dry objectives include scanner (5x), lower power (10x) and high power (40 or 45 x). The oil immersion objective (100x) offers maximum magnification.

Eyepiece: Depending on the type of microscope, the magnified image may travel straight or can be reflected or divided using prism towards the eye piece. Monocular microscopes have single eyepiece where binocular microscopes have two. The magnified image is again magnified in the eyepiece lens and an inverted image is formed on the retina of the viewer’s eye. Older Huyghenian eye pieces were used with achromatic objective lenses but the newer apochromatic objectives require compensating eye pieces. These eye pieces correct the lateral colour errors of their objectives. In a compound microscope, the image is magnified twice; first by the objective lens and then by the eye piece. The eye piece consists of two planoconvex lenses with a circular diaphragm between them. Their magnification can vary form 5x to 10x.

The magnifications of the image in a compound microscope are as follows:

Objective lens	Eye piece	Total magnification
5x	10x	50x
10x	10x	100x
40x	10x	400x
100x	10x	1000x

The image of a specimen is magnified approximately 1000 times using a compound microscope. With an inclined body, the magnification of the microscope may be improved by another 1.5 times. With the highest practically achievable NA of about 1.4, 1400x is the highest useful magnification that can be achieved.

Role of oil: Since the condenser is fully raised for use with oil immersion objectives, light focused on to the specimen are at acute angles. For this reason the objective lens must be as low as possible. Despite this, the light can pass away without entering the objective lens due to diffraction suffered by light when moving from one medium to another (glass to air). Hence, the place between the glass slide and oil immersion objective is filled with immersion oil having same refractive index as that of glass. The light rays leaving the glass do not deviate and enter straight into the objective lens.

Even though the magnification of 1000x is achieved using 100x objective of 1.4 NA and 10x eyepiece, it does not provide image as sharp as that obtained with magnification of 400x using 40x objective of 0.65 NA and 10x eyepiece.

Adjustments for dry objectives (5x, 10x, 40x):

Mirror: concave, condenser: partially lowered, iris diaphragm: partially closed

Adjustments for oil immersion objective (100x):

Mirror: plane, condenser: fully raised, iris diaphragm: fully open

Focusing the slide:

Before viewing the slide under microscope, it is important to obtain a bright background. For oil immersion objective usage, follow these steps:

Ensure that iris diaphragm is fully open and condenser fully risen. With 10x objective in place, look through the eyepiece and adjust the plane mirror such a way that you obtain perfectly bright and uniformly lit white background.

Place a drop of oil on the stained smear and place it on the stage and center it such a way that the smear is above the source of light and below the objective lens.

Shift to 100x objective and raise the stage till the oil on the slide touches the objective. This must be done looking sideways and not while looking through the eyepiece or else the slide will break and damage the objective lens.

Using fine adjustment, try to focus the image. Move the slide accordingly to obtain a good field.

After viewing and noting down the observations, lower the stage and remove the slide.

Proper usage and handling the microscope:

Microscope is a delicate instrument that must be handled with care. All kinds of mechanical shocks must be avoided. The microscope must be lifted by holding its arm in one hard and supporting the base of the microscope with the palm of the other hand. The microscope must be kept in dust free environment. The oil must be wiped clean using a soft tissue paper. After usage the slide must be removed and cleaned before returning to its original place.